Standard Strat Wiring- Part 2

Last Updated on February 24th, 2022

In part 2 we are going to look at a traditional, standard Strat wiring configuration with a 5-way switch and teach you step by step how to get it done. If you haven’t read Part 1 yet, start here.

Connecting the 5-Way Strat Switch

If you remember from Part 1, the anatomy of a 5 way Strat switch, we have two sides: Pole A and Pole B (Fig 1). First, we have to connect both sides of the switch by adding a “jumper” from terminal A0 to B0 (Fig 2).

standard strat wiring figure 1 strat wiring fig 2

Remember A0 and B0 are the common terminals. This allows us to use both sides of the switch for different functions. Once we have both sides connected via the jumper, we can add the pickup hot lead wires to Pole A side of the switch. In a standard Stratocaster wiring configuration, the bridge pickup goes to A1, middle to A2, and neck to A3 (Fig 3). Next, we will attach the Tone 1 (closest to your volume pot) lead wire to B3 and tone 2 to B2. Finally, we’ll attach our volume lead wire to common B0.

5 way switch strat wiring fig 3

All 5 POSITIONS

fig 3A

The Bridge

Simple right?! So what is really happening in a standard Strat wiring? Well, when we select position 1 (Fig 3A), we are sending (connecting) our bridge pickup A1 to common A0. And since the commons are connected via a jumper, the bridge is also being sent to B0. The wiper is also connecting B0 to B1. As you can see from Fig 3A, the bridge shows up in several places. In a traditional Stratocaster guitar wiring, we don’t have a tone pot connected to B1, the bridge is unaffected by either of the tone controls.

Sultans Of Swing (Bridge + Middle)

Now here is where it gets fun. When we select position 2 with our standard 5-way switch wiring, it sends both bridge (A1) and middle (A2) to A0 then to B0 via the jumper. Just like A0, B0 is seeing both bridge and middle pickups. On the pole B side the wiper is connecting B0, B1, and B2 (Fig 4B). Notice tone 2 is connected to B2. Since B0, B1, B2 are connected together via the wiper, when we roll down tone 2 it will affect both pickups by the same amount. The high end is bleeding off to ground for both pickups. Mark Knopfler used position 2 on many Dire Straits songs including his famous tune Sultans of Swing.

Clapton in the Middle

When we select position 3 with our standard 5-way switch wiring, the middle pickup goes from A2 to A0 to B0 to B2. You could take an Ohm reading from any of those terminals and it will read the same middle pickup. (Fig 4C) This position may not be the most popular of the 5 positions but you’ll hear it used by players such as Clapton and SRV to name a few.

fig 4A

Couldn’t Stand the Weather (Middle + Neck)

In position 2 we connected two pickups together. Similarly, position 4 connects the middle and neck pickup together (Fig 4D) . We are sending (connecting) the middle and neck pickup to A0 then over to B0 via the jumper. The wiper on the Pole B side is sending (connecting) middle and neck to two terminals B2 and B3. Therefore, B2 and B3 are also connected to tone 1 and tone 2 respectively.

Since the middle and neck are both connected to tone 1 and tone 2 we can use either one. The tone pot rolled down the most will take precedence over the other. So, if you have tone 1 rolled all the way down but tone 2 all the way up, you will hear only the effect of tone 1 since it’s bleeding off more high end of the two pots to ground. Frequencies are set by the capacitor and the amount is set by where the pot is positioned.

Position 4 is one of the most used Stat positions. You’ll hear players from SRV, Hendrix, to John Mayer use this this juicy position both live and in the studio.

The Wind Cries Mary (Neck)

Last but not least, we have position 5 (Fig 4E). We all love a good neck tone right?! Using the standard Strat wiring in this position, the neck pickup goes from A3 to A0 to B0 to B3. Tone 2 is connected to B3 which allows us to set our desired tone level to the neck pickup. Position 5 is another common position among blues, rock, and jazz players.

More than 1-way!

Now, one thing may have crossed your mind. Why not hook up the tone lead wires to the Pole A side terminals A2 and A3? Wouldn’t that essentially do the same thing without having to use a jumper? Good question young padawan. You are absolutely right! The switch would function the same if you kept the jumper from A0 to B0 or move your volume lead wire to A0.
Stratocaster guitar
So why does Fender wire Strats this way? We suspect the reasons the standard Strat wiring originally utilized the switch this way are twofold: firstly, Fender already had lots and lots of three-way, two-pole switches in stock because they needed them for the Telecaster; and secondly, it’s easier to solder one wire to a contact than it is to solder two. If they already had those switches, why not make it easier to solder?

The good news is there’s a good reason to leave the jumper connected to A0 and B0. This jumper will allow us to mod our switch to better suit our specific playing styles.

Check out part 3 where we look at a few ways to re-wire your standard Strat wiring for more options. And the good news is you don’t have to buy extra parts.  Hallelujah! Mod time…

3 replies on “Standard Strat Wiring- Part 2”

Archives

Please check your items carefully and confirm they are correct for color, position, etc. We are not able to accommodate order changes or cancellations once you have completed the check out process.

My cart
Your cart is empty.

Looks like you haven't made a choice yet.